FAA ordering more inspections of Boeing 737s
DALLAS (AP) - Federal safety officials said Monday they are ordering additional inspections of some Boeing 737 jets after a hole tore open in a Southwest Airlines plane during flight in 2009.
The Federal Aviation Administration said that it will seek more detailed inspections for cracks along the tops of the planes.
The FAA estimated that the cost of inspecting 109 older Boeing 737s will be about $5.2 million. The agency said it has no idea how many planes will need repairs.
The order will cover 737-300, -400 and -500 models of the popular passenger aircraft. Southwest's entire fleet is Boeing 737s, although many are newer -700 and -800 models. The agency said repairs could cost up to $17,765 per plane, or $1.94 million for all 109 U.S.-registered planes covered by the order.
The FAA said it would publish an order covering the inspections in Wednesday's Federal Register.
The FAA issued rules in 2005 to detect metal fatigue caused by pressurizing the cabin during every flight - hundreds of times per year.
In a statement on Monday, the agency said those rules would be expanded to include new inspection methods with scanning technology, checks of more areas of the plane, the installation of additional reinforcements and checks for loose fasteners.
The agency published a proposal for additional inspections in January 2012, and it was endorsed by the National Transportation Safety Board, which investigates accidents and other safety incidents.
Boeing spokesman Miles Kotay said the new inspections were "already well under way - hundreds already have been completed worldwide, with few findings" of additional problems with cracking along the planes' crowns.
Brandy King, a spokeswoman for Dallas-based Southwest Airlines Co., said the airline was prepared to comply with the FAA and does not expect any impact on Southwest flight schedules while the inspections are done.
"We remain completely confident in the airworthiness of our fleet," she said.
The new FAA requirements stem from a 2009 incident in which a Southwest flight from Nashville to Baltimore had to make an emergency landing in Charleston, W.Va., after a hole more than a foot long appeared in the roof near the tail. Boeing issued a special service bulletin to airlines operating the planes in 2010.
In 2011, a different Southwest jet was forced to land in Yuma, Ariz., but authorities believe that incident involved cracking in a different type of joint where panels of aluminum skin overlap.
The Federal Aviation Administration said that it will seek more detailed inspections for cracks along the tops of the planes.
The FAA estimated that the cost of inspecting 109 older Boeing 737s will be about $5.2 million. The agency said it has no idea how many planes will need repairs.
The order will cover 737-300, -400 and -500 models of the popular passenger aircraft. Southwest's entire fleet is Boeing 737s, although many are newer -700 and -800 models. The agency said repairs could cost up to $17,765 per plane, or $1.94 million for all 109 U.S.-registered planes covered by the order.
The FAA said it would publish an order covering the inspections in Wednesday's Federal Register.
The FAA issued rules in 2005 to detect metal fatigue caused by pressurizing the cabin during every flight - hundreds of times per year.
In a statement on Monday, the agency said those rules would be expanded to include new inspection methods with scanning technology, checks of more areas of the plane, the installation of additional reinforcements and checks for loose fasteners.
The agency published a proposal for additional inspections in January 2012, and it was endorsed by the National Transportation Safety Board, which investigates accidents and other safety incidents.
Boeing spokesman Miles Kotay said the new inspections were "already well under way - hundreds already have been completed worldwide, with few findings" of additional problems with cracking along the planes' crowns.
Brandy King, a spokeswoman for Dallas-based Southwest Airlines Co., said the airline was prepared to comply with the FAA and does not expect any impact on Southwest flight schedules while the inspections are done.
"We remain completely confident in the airworthiness of our fleet," she said.
The new FAA requirements stem from a 2009 incident in which a Southwest flight from Nashville to Baltimore had to make an emergency landing in Charleston, W.Va., after a hole more than a foot long appeared in the roof near the tail. Boeing issued a special service bulletin to airlines operating the planes in 2010.
In 2011, a different Southwest jet was forced to land in Yuma, Ariz., but authorities believe that incident involved cracking in a different type of joint where panels of aluminum skin overlap.
Neither the FAA nor FDA inspire confidence, and I don't believe it has a thing to do with the size of Government. It's corrupt corporate influence on said Government.
Four years to issue an airworthiness directive? Hope it didn't interfere with the coffee break for some FAA director.
So it's 2012 nearly 2013 and they are just ordering this now? What the heck?
 @PrairieDawn Yep that's bureaucracy for ya. Kind of like when the FDA approves a drug and "finds out" 3 years later when they're bad. But hey, over half the country believes more government is great.
That's how ya fix anything! Blue tarp and duct tape! http://blog.onlinemetals.com/wp-content/uploads/2011/11/engineering-flowchart.jpg
Sounds like the "campaign contributions" were a little light this year.
Inspector: Well, that there looks like a Boeing 737 with a hole in the fuselage.  Hmm.
Â
Ariline: I reckon so. Don't make the the way they used too I guess Mr. G man.
Â
Inspector: Guess we are done here. You paid your inspection fees. Here is some union duct tape.
This is very old news to those in the know...........................just saying!  Happy New Year!!!!  Fly safe everyone!!